Skip to content
Bukhara, Uzbekistan · Hunarmand Association

Forged in the
Oldest Craft
of Bukhara

Knives, daggers and the bird-shaped scissors of Bukhara, made by hand in a brick furnace my family has worked for generations. Damascus steel folded in the workshop, horn and mulberry wood shaped by hand, every blade finished so it doesn't break, doesn't bend, and cuts well.

10+ Years at the forge
40 Smiths left in Bukhara
6 Apprentices in the workshop
Two smiths striking a glowing billet on the anvil, the furnace burning behind them
Bayramali Sayfilloev beside the brick furnace in his Bukhara workshop
Workshop

Bukhara, Uzbekistan

Family trade

1200°C Forge-welding heat

My furnace is built of chamotte brick and can be heated by natural gas, propane, wood or coal. It is fitted with a pair of bellows.

Our Heritage

One of the Oldest
Crafts in Bukhara

The blacksmith's handicraft of Bukhara is considered one of the oldest, because from the very beginning man was engaged in working metal. In the 10th century Abu Rayhon Beruni wrote that the master smiths of Bukhara worked in four kinds of metal. Earlier they made damask sabres and knives, medical instruments, manicure sets, fitters' tools and sewing accessories, all of them valued among the merchants of the Great Silk Road.

By the end of the 19th century there were over a hundred and fifty smiths in Bukhara — nail makers, farriers, locksmiths, iron tool makers, needle makers, tinsmiths, cutlers. About forty are still working. I learned this craft from my father and my grandfather, and I work now in my own workshop with six apprentices. We are cousins. It is a family business.

Temirchiliq Blacksmith's work
Kordgari Knife making
Usto–Shogird Master to apprentice
Pichoq The Uzbek knife
Commission a Blade
What I Make

Blades Made to Be
Used for a Lifetime

Brass and copper bird scissors laid on maroon velvet
Bukhara only Still used by the city's
gold embroiderers
A Bukhara Form

Nightingale and
Heron

Nightingale and heron scissors, a form you will find nowhere but Bukhara, still used by the city's gold embroiderers.

My favourite shape of blade is the tolbargi pichoq, shaped like a willow leaf. Others have the almond shape, the kamalak pichoq, with a channel running along the upper edge of the blade.

See the Work
The Technique

Fire, Steel and
Everything After

The process has few steps, but none of them can be hurried. I use low carbon steel, high carbon steel, and Damascus steel that I forge myself. Used parts from cars, engines and machinery are a very good source of steel. Everything I need is available in the markets here.

01

Forging

First we warm up the furnace, then put the chosen steel in and keep it there until it reaches forging temperature, usually 800 to 1000 degrees. Then it is forged with sledgehammers on the anvil. If the piece is light enough one smith can forge it, holding it in tongs in the left hand and hammering with the right. A heavy piece takes two people. When it cools we heat it again, and we repeat that several times.

02

Damascus

Making Damascus steel in Bukhara is comparatively new. The technology was forgotten during the 20th century and only revived at the end of it by some of the local blacksmiths. I pick the flat bars I need for their hardness, flexibility and softness, and forge them into a single solid piece. The order matters: hard steel in the centre, the more flexible steels at the sides. Chosen properly, the edge of the blade comes out very hard and the body stays flexible. The pattern on the surface comes from inside.

03

Hardening and Tempering

To harden a blade I heat it and then put it straight into water or oil to cool it immediately. If it is heated too much the steel becomes brittle and the cutting edge suffers, so the temperature is strictly controlled. A hardened blade that has had no further treatment is brittle, so it is heated again until it reaches the right level of softness. Hardening shrinks the steel slightly and warps it, and the blade is straightened with a copper mallet.

04

Finishing and Handles

A revolving whetstone hones the blade, with water poured over it continuously so the friction does not soften what has just been hardened. Sandpaper polishes the blade until it is like a mirror, which makes it more rust-resistant and more hygienic. Fitting the handle is the last stage: epoxy resin is set into the joint so water cannot get in and start rust. For handles I use deer horn, wood, bone and plastic.

Making a blade this way, being careful about every step, lets me say that I have made a knife that doesn't break, doesn't bend, and cuts well.

Sledgehammers · smaller hammers · anvils · rough grinding machine · chisels and tongs · wire brush · files · grinding stones and abrasive paper · a chamotte-brick furnace with a pair of bellows

The workshop furnace beside a table of finished knives
Fitting a handle to a finished blade at the bench
Striking hot metal at the mouth of the furnace, sparks flying
How It Works

From Steel to Heirloom

Enquiry

Tell me what the blade is for, how long you want it, and what you would like in the hand.

Steel & Handle

We settle the steel — hard, soft, or Damascus forged for you — and the handle in horn, wood, bone or metal.

Forging

The blade is forged, hardened, tempered, straightened and polished. A Damascus blade takes considerably longer.

Delivery

The handle is set with epoxy resin, the blade is finished, and the piece is packed and sent.

Assembling a knife at the workbench

“A youth from a family of masters of many generations does not have to go through the initiation rite. Blacksmiths-to-be are taught the skill from childhood. First the apprentices perform simple operations, but gradually the tasks become more complicated, and by the time they reach fifteen, they work as the equal of adults.”

Sh. Kamalov, hereditary blacksmith of Bukhara

Holding a finished blade in front of the workshop display wall
✦ No minimum order I work to your design as readily as to my own.
Custom Work

A Blade Made
Only for You

There is no minimum order. I work to your design as readily as to my own, and I keep to the date I give you.

Kitchen and working knives in hard steel
Hunting knives in Damascus steel
Daggers and long blades
Bird scissors, made the Bukhara way
Forged ornament — candlesticks, statues, architectural pieces
Start a Commission
Cover of the book The Blacksmith's Handicraft of Uzbekistan
The Blacksmith's Handicraft of Uzbekistan Bayramali Sayfilloev Ma'rifat Publishing House · Tashkent · April 2016
Recognition
  • Hunarmand — National Association of Artisans of Uzbekistan
  • National awards for traditional blacksmithing
  • International art exhibitions
  • Featured in Buxoroi Sharif, national press
  • Author — The Blacksmith's Handicraft of Uzbekistan, Tashkent, 2016
Get in Touch

Let's Make
Something Lasting

Every blade begins with a conversation about what you need it to do. Write to me and tell me what you have in mind.

bayram_inc@yahoo.com Bukhara, Uzbekistan